Arduino/Lauflicht mit Schalter und Potentiometer: Unterschied zwischen den Versionen

Aus ZUM-Unterrichten
main>Karl Kirst
K (int. Link)
main>Belofb
Keine Bearbeitungszusammenfassung
Zeile 3: Zeile 3:
Das [[Arduino]]-Board wurde zusammen mit zwei Steckplatinen auf einer Holzplatte befestigt, um die Handhabbarkeit für den Unterricht in der Schule zu verbessern. Für die Befestigung des Arduino-Boards auf der Platte gibt es hier einen [https://www.flickr.com/photos/johngineer/5484250200/ Bohrplan].
Das [[Arduino]]-Board wurde zusammen mit zwei Steckplatinen auf einer Holzplatte befestigt, um die Handhabbarkeit für den Unterricht in der Schule zu verbessern. Für die Befestigung des Arduino-Boards auf der Platte gibt es hier einen [https://www.flickr.com/photos/johngineer/5484250200/ Bohrplan].


Die Steuerung schaltet 3 LEDs, die als Lauflichter funktionieren. Der Taster dient dazu, das Lauflicht anzuschalten. Das Lauflicht bleibt solange an, wie der Taster gedrückt bleibt. Die Zeitdauer, die jede LED an ist, wird über ein an PIN A0 angeschlossenes Potentiometer eingestellt. Der ausgelesene Wert wird in der Variablen "potiVal".


Sourcecode für Arduino-Sketch mit ausführlicher Kommentierung (englischsprachig)
:/*
:  Light chaser with pushbutton and variable speed
:  Turns on and off LED1, then turns on and off LED2 and now turns on and off LED3.
:  After this the procedure starts again.
:  The loop routine runs only when the pushbutton switch is pressed.
:  The chasing frequency can be set by the potentiometer.
:  */
:
:// Pin numbers are allocated to the variables led1, led2 and led3
:// the digital input (pushbutton) and the analog input (potentiometer) are selected
:// the variables for the inputs are chosen and set to 0 at the beginning of the sketch
:
:const int led1 = 11; //  11 (for LED Pin 11) is allocated to the variable led1
:const int led2 = 12; //  12 (for LED Pin 12) is allocated to the variable led1
:const int led3 = 13; //  13 (for LED Pin 13) is allocated to the variable led1
:const int button = 7; // 7 (for button Pin 7) is allocated to the variable button
:const int potiPin = A0; // A0 (for potentiometer Input Pin A0) is allocated to the
:                          //variable potiPin
:
:int val = 0;  // the variable to store the state of the input pin 7 (button)
:                //is defined (val) and set to 0 (LOW) at the beginning of the sketch.
:int potiVal = 0;  // the variable to store the value coming from analog input pin 7
:                  //(potentiometer) is defined (potiVal) and is set to 0 at the
:                // beginning of the sketch
:
:// the setup routine runs once when you press reset:
:
:void setup() {               
:  // initializes the digital pins 11, 12 and 13 as outputs.
:  pinMode(led1, OUTPUT); //led1 or pin 11 is an output
:  pinMode(led2, OUTPUT); //led2 or pin 12 is an output
:  pinMode(led3, OUTPUT); //led3 or pin 13 is an output 
:}
:
:// the loop routine runs as long as the pushbutton is pressed
:void loop() {
:  {
:  val = digitalRead(button);//read input value and store it
:  //check whether the input is HIGH (button)pressed
:  if (val == HIGH) { 
:   
:  potiVal = analogRead(potiPin); // read the value from the sensor                   
:     
:  digitalWrite(led1, HIGH); // turn the LED1 on (HIGH is the voltage level)
:  delay(potiVal);              // wait for a second
:  digitalWrite(led1, LOW);  // switch LED1 off by setting the voltage to LOW
:  digitalWrite(led2, HIGH); // turn the LED2 on by setting the voltage to HIGH
:  delay(potiVal);              // wait for a second
:  digitalWrite(led2, LOW);  //switch LED2 off by setting the voltage to LOW
:  digitalWrite(led3, HIGH); // turn the LED3 on by setting the voltage to HIGH
:  delay(potiVal);              // wait for a second
:  digitalWrite(led3, LOW);  // switch LED3 off by setting the voltage to LOW
:  } else {
:   
:  digitalWrite(led1, LOW);  // switch LED1 off by setting the voltage to LOW
:               
:  digitalWrite(led2, LOW);  //switch LED2 off by setting the voltage to LOW
:   
:  digitalWrite(led3, LOW);  // switch LED3 off by setting the voltage to LOW
:    }
:}}


{{SORTIERUNG:{{SUBPAGENAME}}}}
{{SORTIERUNG:{{SUBPAGENAME}}}}
[[Kategorie:Arduino]]
[[Kategorie:Arduino]]

Version vom 11. September 2014, 17:17 Uhr

Arduino-Lauflicht mit Schalter und Potentiometer.JPG

Das Arduino-Board wurde zusammen mit zwei Steckplatinen auf einer Holzplatte befestigt, um die Handhabbarkeit für den Unterricht in der Schule zu verbessern. Für die Befestigung des Arduino-Boards auf der Platte gibt es hier einen Bohrplan.

Die Steuerung schaltet 3 LEDs, die als Lauflichter funktionieren. Der Taster dient dazu, das Lauflicht anzuschalten. Das Lauflicht bleibt solange an, wie der Taster gedrückt bleibt. Die Zeitdauer, die jede LED an ist, wird über ein an PIN A0 angeschlossenes Potentiometer eingestellt. Der ausgelesene Wert wird in der Variablen "potiVal".

Sourcecode für Arduino-Sketch mit ausführlicher Kommentierung (englischsprachig)

/*
Light chaser with pushbutton and variable speed
Turns on and off LED1, then turns on and off LED2 and now turns on and off LED3.
After this the procedure starts again.
The loop routine runs only when the pushbutton switch is pressed.
The chasing frequency can be set by the potentiometer.
*/
// Pin numbers are allocated to the variables led1, led2 and led3
// the digital input (pushbutton) and the analog input (potentiometer) are selected
// the variables for the inputs are chosen and set to 0 at the beginning of the sketch
const int led1 = 11; // 11 (for LED Pin 11) is allocated to the variable led1
const int led2 = 12; // 12 (for LED Pin 12) is allocated to the variable led1
const int led3 = 13; // 13 (for LED Pin 13) is allocated to the variable led1
const int button = 7; // 7 (for button Pin 7) is allocated to the variable button
const int potiPin = A0; // A0 (for potentiometer Input Pin A0) is allocated to the
//variable potiPin
int val = 0; // the variable to store the state of the input pin 7 (button)
//is defined (val) and set to 0 (LOW) at the beginning of the sketch.
int potiVal = 0; // the variable to store the value coming from analog input pin 7
//(potentiometer) is defined (potiVal) and is set to 0 at the
// beginning of the sketch
// the setup routine runs once when you press reset:
void setup() {
// initializes the digital pins 11, 12 and 13 as outputs.
pinMode(led1, OUTPUT); //led1 or pin 11 is an output
pinMode(led2, OUTPUT); //led2 or pin 12 is an output
pinMode(led3, OUTPUT); //led3 or pin 13 is an output
}
// the loop routine runs as long as the pushbutton is pressed
void loop() {
{
val = digitalRead(button);//read input value and store it
//check whether the input is HIGH (button)pressed
if (val == HIGH) {
potiVal = analogRead(potiPin); // read the value from the sensor
digitalWrite(led1, HIGH); // turn the LED1 on (HIGH is the voltage level)
delay(potiVal); // wait for a second
digitalWrite(led1, LOW); // switch LED1 off by setting the voltage to LOW
digitalWrite(led2, HIGH); // turn the LED2 on by setting the voltage to HIGH
delay(potiVal); // wait for a second
digitalWrite(led2, LOW); //switch LED2 off by setting the voltage to LOW
digitalWrite(led3, HIGH); // turn the LED3 on by setting the voltage to HIGH
delay(potiVal); // wait for a second
digitalWrite(led3, LOW); // switch LED3 off by setting the voltage to LOW
} else {
digitalWrite(led1, LOW); // switch LED1 off by setting the voltage to LOW
digitalWrite(led2, LOW); //switch LED2 off by setting the voltage to LOW
digitalWrite(led3, LOW); // switch LED3 off by setting the voltage to LOW
}
}}